Part Number Hot Search : 
0430201 HC00A 2SD1856 TA124 H2005A 00400 C1203 AH116
Product Description
Full Text Search
 

To Download RH1086DICE Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 DICE SPECIFICATION RH1086K/RH1086H 1.5A/0.5A Low Dropout Positive Regulators
PAD FUNCTION
2 1 2
DIE CROSS REFERENCE
LTC Finished Part Number RH1086H RH1086K Order DICE CANDIDATE Part Number Below RH1086H DICE RH1086K DICE
1. 2. 3.
VIN VOUT ADJUST
2
Connect Backside Substrate to Pad #2
3
103 x 85 mils
DICE ELECTRICAL TEST LI ITS (Note 1)
PARAMETER
Reference Voltage Line Regulation Load Regulation
CONDITIONS
IOUT = 10mA, TJ = 25C, (VIN - VOUT) = 3V 1.5V (VIN - VOUT) = 15V ILOAD = 10mA, 1.5V (VIN - VOUT) 15V TJ = 25C (VIN - VOUT) = 3V, 10mA IOUT 1.5A TJ = 25C (0.5A for RH1086H) (Notes 1, 2, 5, 6) VOUT, VREF = 1%, IOUT = 1.5A (0.5A for RH1086H) (Notes 3, 5, 6) (VIN - VOUT) = 5V (VIN - VOUT) = 25V (Note 5) (VIN - VOUT) = 25V (Note 4) f = 120Hz, COUT = 25F Tantalum IOUT = 1.5A, (IOUT = 0.5A for RH1086H) CADJ = 25F, (VIN - VOUT) = 3V (Note 5, 6) TJ = 25C 10mA IOUT 1.5A (0.5A for RH1086H) 1.5V (VIN - VOUT) 15V (Note 5, 6)
Dropout Voltage (VIN - VOUT) Current Limit Mininum Load Current Ripple Rejection
Adjust Pin Current Adjust Pin Current Change
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
W
RH1086K (Note 6) MIN MAX
1.238 1.225 1.262 1.270 0.2 0.3
RH1086H (Note 6) MIN MAX
1.225 1.270 0.2 0.3
UNITS
V V % %
1.25 1.5 1.5 0.050 10 60 60 0.5 0.020 10
V A A mA dB
120 5
120 5
A A
1
DICE SPECIFICATION RH1086K/RH1086H
DICE ELECTRICAL TEST LI ITS
Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Load and line regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead 1/8" from the package. Note 2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W for the RH1086K, 3W for the RH1086H. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output voltage range. See Short Circuit Current Curve in the LT1086 Series standard data sheet for available output current. Note 3: Dropout voltage is specified over the full output current range of the device. Test points and limits are shown on the Dropout Voltage Curve in the LT1086 Series standard data sheet. Note 4: Minimum load current is defined as the minimum output current required to maintain regulation. At 25V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. Note 5: Guaranteed by design but not tested at wafer sort. Note 6: For compliance with 883 revision C current density spec. RH1086K is derated to 1.0A max load operation.
Rad Hard die require special handling as compared to standard IC chips. Rad Hard die are susceptible to surface damage because there is no silicon nitride passivation as on standard die. Silicon nitride protects the die surface from scratches by its hard and dense properties. The passivation on Rad Hard die is silicon dioxide that is much "softer" than silicon nitride. LTC recommends that die handling be performed with extreme care so as to protect the die surface from scratches. If the need arises to move the die around from the chip tray, use a Teflon-tipped vacuum wand. This wand can be made by pushing a small diameter Teflon tubing onto the tip of a steel-tipped wand. The inside diameter of the Teflon tip should match the die size for efficient pickup. The tip of the Teflon should be cut square and flat to ensure good vacuum to die surface. Ensure the Teflon tip remains clean from debris by inspecting under stereoscope. During die attach, care must be exercised to ensure no tweezers touch the top of the die. Wafer level testing is performed per the indicated specifications for dice. Considerable differences in performance can often be observed for dice versus packaged units due to the influences of packaging and assembly on certain devices and/or parameters. Please consult factory for more information on dice performance and lot qualifications via lot sampling test procedures. Dice data sheet subject to change. Please consult factory for current revision in production.
I.D. No. 66-11-1086
2
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 FAX: (408) 434-0507 www.linear-tech.com
W
LT 0599 50 Rev A * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 1998


▲Up To Search▲   

 
Price & Availability of RH1086DICE

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X